Model		GJS03-M1AX- 96-***
Size:With clamp’s biggest outer dia.	422.3*219.2 mm	Raw material	Dome, Base： modified PP,  clamp：Nylon +GFTray: ABSMetal parts：Stainless steel
Entry ports number:	1 oval port，4 round ports	Available cable dia.	Oval port：available for 2 pcs, 10~29mm cablesRound ports：Each available for 1pc 6-24mm cable
Max. tray number	4 trays	Base sealing method	Heat-shrink
Tray capacity	24F	Applications	Aerial, directly buried, Wall/pole mounting
Max. closure splice capacity	96F	IP grade	68

1. Working Temperature: -40 degrees centigrade~+65 degrees centigrade 2. Atmospheric Pressure: 62~106Kpa 3. Axial Tension: >1000N/1min 4. Flatten Resistance: 2000N/100 mm (1min) 5. Insulation resistance: >2*104MΩ 6. Voltage Strength: 15KV(DC)/1min, no arc over or breakdown 7. Temperature recycle: under -40℃~+65℃，with 60(+5)Kpa inner pressure, in 10cycles; Inner pressure shall decrease less than 5 Kpa when closure turn to normal temperature. 8. Durability：25 years

Name	Qty	Picture		Name		Qty		Picture
Dome	1pc			Tray		Max.4 pcsoptional		RQP-06-24c middle splice
								RQP-08-24c side splice
Clamp	1pc			Valve		1		optional
Base	1pc			Modified O-ring		1
Cable Strengthen member attach plate	1set			Velcro strip with one X flake		1
optic joints protection tube	Max. 96			Ground feed-through lug		1	optional
Metal Storage basket	1 standard offered			Plastic storage basket		1Orderd as optional
Nylon tie &  Transparent PE tube	8pcs/bag	Each two trays with 1 bag.
Wall mounting kits	1Standard offered with
Aerial mounting kits	Order as optional
Pole mounting kits	Order as optional
Round Port accessories bag	1 bag		Items		Heat-shrink tube		4
					Abrasive tape		1
					Aluminium foil		4
Oval port accessories bag	1bag		Items		Heat-shrink tube		1
					Abrasive tape		1
					Aluminium foil		2
					Cleaning tissue		1		optional
					Desiccant		1		optional
					Shield continuity wire		1		optional
					AMP clamp		1		optional
					Branch off clip		1

2. Put the cable through the heat-shrink tube4. Remove the loose tube of the cable and clean the bare fibers. Put them through the transparent PE tube. Using PVC tape to wrap the end of the PE tube and cable.1. Cut the ports need to guide-in cable3. Remove the sheath of the cable and clean it. Cut the strengthen member to 5cm length. Put it through the attach screws and bend it to fix on the screw. Then tighten the screw.6. Coiling the optic fibers in the splice trays as above picture from the bottom tray to the top one. Fusion the joints and shrink the protective tubes and fix them in the tray. And put on the tray lid.13.Choose the suitable mounting kits for different installation environment.5. Wind the excessive loose buffers in suitable cycles and put in the storage basket.7. Use the Velcro strip to bind the trays.9. Clean the cable surface and ports10. Move the heat-shrink tube to cover the base port and the cable. Mark the tube end on the cable and stick the aluminum film on it. The blue line of the film shall at the same position of the marked place. ( Edge which close to the blue line shall be in the tube. Other side out of the tube.) Using blunt tool to even the film tightly stick to the cable.  Heat the tube to shrink to seal from the direction of the red arrow slowly. (If to guide 2 cables in the oval port, use branch off clips to separate the cables , heat the branch off clip at meantime to seal the space.)8.Using abrasive strip to rough the surface of the cable sheath and ports slightly.11. heat the round ports follow the same step as the oval port12.  close the closure with the clamp.